How To Open Ps4 Controller Without Screwdriver

Unscrew The Back Cover

Take Apart a PS4 Controller Without Breaking It

You will need to remove the three screws at the top back of the PS4. They might be covered by stickers which you can remove with a knife or a flathead screwdriver.

The best way to remove the screws without damage is with a T9 Torx security bit screwdriver. If you cant get your hands on one of those screwdrivers, you can use a 2mm flathead screwdriver instead. But just note that this will strip the screws.

Keep the screws in a safe place and gently remove the back cover by gently lifting it from the back, near the power unit, first.

Will A T10 Work On A Ps4

Xbox 360 console, Xbox 360 controller, PlayStation 3 thin and fat, PlayStation 4 , cant open PS4 controllers will need an additional Philips screwdriver. -T10 Security Torx set -a selection of screwdrivers and Torx sets, each of which is capable of opening the aforementioned devices in order to facilitate your repairs.

Repair Of Buttons Dualshock 4

Clean main board with cotton swabs.

If some button dont react push each time you can try to recover its functionality with graphite pencil. This method in most cases helps, but not always.

Now start to assemble gamepad

Place main board to its place in the case.

Connect touchpad cable to main board.

Secure the board with screw.

Now place battery securing area on main board.

Place battery to securing area and connect it to main board.

Connect backlight cable to main board. Take attention the way that cable must be connected, if it be connected upside down backlight wont work.

Gamepad bottom case must be installed starting from upper edge, where left and right triggers placed.

Now check if something would interrupt snaping of bottom edge of gamepad case, if theres not snap it.

Now when gamepad case fully closed check if gamepad works by pushing PS button and watching backlight indicator.

If its all right secure case by tighten screws.

You May Like: How To Disassemble Ps4 Controller

Cleaning The Inside Of The Controller

1Remove the 4 screws from the back of the controller. Flip the controller over. Remove all of the screws by turning each screw counterclockwise with a Phillips #0 flat head screwdriver. Use a 4 to 5 inch screwdriver for the best results.XResearch source

Replace the screws if they are difficult to turn. The screws are M2X6 Phillips flat head machine screws.

2Insert a small flathead screwdriver into the crease and lever it open. Press the screwdriver firmly in between the crease at any point along the controller. Begin levering it up until the pieces open. Continue working around the crease until it pops open completely.XResearch source

Be gentle when levering open the controller to avoid damaging it.

3Remove the back piece of the controller. Pull the controller apart from the indent on the bottom between the analog sticks. Gently remove the back of the controller by jiggling it up and forward. Take care not to pop the buttons off.XResearch source

Spray the back piece with a surface cleaner and dry cloth if it’s dirty.

4Pull out the white ribbon cable from the connector slot. After opening the controller, take care not to break the ribbon cable. Gently remove it from its connector slot with your hands and set the front piece of the controller aside.XResearch source

Be patientâthis piece can take a while to shimmy off.

Be careful not to break the wires attaching the chipboard to the battery.

Reattach any ribbon cables as you reassemble the controller.

Clean With Cotton Swabs

Best How To Open Ps4 Controller Without Screwdriver

Wearing gloves, soak a cotton swab with isopropyl alcohol. Flatten the cotton bud, so the end is flat. Now you can get it into the small crevices, like the gaps around the buttons, all around the thumbsticks , and trigger buttons .

Top Tip

When cleaning the thumbsticks, move them around to expose the entire base. Wipe down all areas of the base to ensure that its all 100% clean.

Don’t Miss: Can I Play Destiny Without Playstation Plus

Removing A Flat Head Screw

1Use this method to remove a flat head screw without a screwdriver. A flat head screw has one groove across the head of the screw only. If you do not have a flat head screwdriver then you can usually use any kind of flat surface to unscrew the screw.

2Use a card. Try using a card such as a plastic credit card to turn the screw. Insert the edge of the card into the long groove and turn counterclockwise to unscrew the screw. Make sure the card is strong and old as it could be damaged in the process.

3Try the tab from a can of soda. Remove the tab from a can of soda and insert into the groove on the head of the flat head screw. Turn the head counterclockwise to unscrew the screw.

4Try a coin. Try inserting a small coin into the groove and turning counterclockwise to unscrew. Dimes and pennies are particularly useful for this method but larger coins will be easier to turn if they fit in the groove.

5Find a kitchen butter knife. Kitchen butter knives can be used in a very similar way to coins. Insert the end of the butter knife into the groove and turn counterclockwise to unscrew the screw.

If your butter knife is of low quality and strength or the screw is very tight, then you may bend your butter knife rather than unscrewing the screw. Be aware of this potential damage.

Needle nose pliers may work better than regular pliers.

How To Reassemble The Ps4 Controller

Once you have finished cleaning the inside and outside, the next step is reassembling the controller. To do this, follow the steps below:

Insert the battery pack into the back of the controller . Make sure that it is properly seated and secure.

Line up the two halves of the controller so that they are facing the correct way. The triggers should be outside, and the joysticks should be in the center.

Attach the triggers to the controller using the screws.

Next, attach the buttons. Start with the face buttons , then move on to the shoulder buttons .

Finally, attach the joysticks. Be sure to line them up correctly so that they are flush with the controller’s surface.

Once the pieces are in place, you can screw in the back panel to secure everything.

Don’t Miss: How To Delete Worlds In Minecraft Ps4

Can You Get Your Ps4 Professionally Cleaned

We get it. Cleaning your PS4 is an intimidating and time-consuming task. If you dont have experience cleaning gadgets, you might be worried about breaking your console.

You can take your PS4 to your local game shop, electronics store, or electronic repair shop to ask whether theyll professionally clean your device for you.

Wipe With Water Or Alcohol

How to open your PS4 controller easily with no damage

If the disc is still dirty after the above step, issue a deeper clean with water or alcohol. Dampen a cloth in water or diluted isopropyl alcohol and wipe the disc from the center to the edges, moving in straight lines. Dry the disc afterward with a separate dry, microfiber cloth.

Be Safe

Dont soak the disc. When you dampen the cloth in a liquid, wring it out extremely well. Soaking the disc could cause permanent damage.

Recommended Reading: How To Make Your Ps4 Quieter

Cleaning The Joysticks And Buttons

Like the other parts of the controller, the most effective way to clean the joysticks and buttons is to use rubbing alcohol and a cotton swab. You can follow these steps to clean them.

First, pop off the joysticks and pull off the cradles holding the buttons to remove them.

Now, dip the cotton swab or clean cloth in the alcohol and gently rub it over the buttons. Move the cotton swab around frequently to avoid spreading dirt and grime everywhere.

Next, using the cloth, clean the sockets of the buttons thoroughly, as shown below.

Once you’re finished, let the controller joysticks and buttons dry before inserting them into the controller again.

How To Open Your Ps4 Without A Torx Screwdriver

There are a few ways that you can open your PS4 without a Torx screwdriver. One way is to use a paperclip. Another way is to use a small flathead screwdriver.

If you are using a paperclip, you will need to insert it into the tiny hole in the bottom left corner of the PS4. You will then need to twist the paperclip until you feel it click. This will release the casing and allow you to open your PS4.

If you are using a small flathead screwdriver, you will need to insert it into the hole in the bottom left corner of the PS4. You will then need to twist the screwdriver until you feel it click. This will release the casing and allow you to open your PS4.

Recommended Reading: How To Change Your Profile Picture On Ps4

How To Clean A Ps4 Slim And Pro

When cleaning a PS4 Slim or Pro, the good news is that you can remove the cover without voiding the warranty. So get inside of the console for a deeper clean!

When removing the cover for the PS4 Slim and Pro, its much easier. Simply pull on the left and right corners at the front of the console. Then pull at the bottom, slide the cover back, and it will be easy to remove.

With the PS4 Slim, the fan inside has a cover over it. You can clean it the same way as you would with the original, by blowing condensed air into the vents and wiping the blades with a cotton swab.

On the PS4 Pro, there isnt a cover over the fan. You will see the fan right away after youve removed the main PS4 cover.

How To Open Ps4 To Clean Fan

Before you learn how to clean PS4 fans, you need to open up your PlayStation to access the fans. Well show you how.

But remember that following these steps will void the warranty since youve disassembled your device. So only do this if youre okay with that knowledge.

Time: 15 minutes

Knife or flathead screwdriver

Also Check: How To Get Your Playstation Out Of Safe Mode

Removing A Phillips Head Screw

1Use this method when trying to remove a Phillips head screw without the proper screwdriver. Phillips head screws are those that have two grooves forming a cross. In some cases one of the grooves will be longer than the other if one groove is longer, this is the groove you should use when trying to unscrew your screw because it is easier to use with a variety of improvised tools.

Phillips head screws are particularly prone to being stripped, when the corners formed by the grooves are worn. This makes it very difficult to unscrew your screw because there are no longer solid grooves in which to insert your tool. Be very careful when using these methods so as not to strip your screw.

2Find a kitchen butter knife. Kitchen butter knives can be used in a very similar way to coins. Insert the end of the butter knife into the longer groove and turn counterclockwise to unscrew the screw.

If your butter knife is of low quality and strength or the screw is very tight, then you may bend your butter knife rather than unscrewing the screw. Be aware of this potential damage.XResearch source

3Try a coin. Try inserting a small coin into the longer groove and seeing if it will turn the screw. Dimes and pennies are particularly useful for this method. This will usually only work for larger sized screws rather than very small ones.

Insert the coin into the larger groove and turn counterclockwise.

Needle nose pliers may work better than regular pliers.

What Tools Do You Need To Open Ps4 Pro

This screwdriver repair tool kit is intended for use in disassembling PS5, PS4 PRO, PS4, PS4 Slim Console, and PS4 controllers. The package includes T8H and T9H torx screwdrivers as well as PH00 and PH0 Phillips screwdrivers. T9H Torx Screwdriver: The rear of the PlayStation 4 employs T9 Screws, and in order to unscrew those, you will need a T9 Torx Security Screwdriver.

Read Also: What Screwdriver To Open Ps4

Cleaning The Front And Rear Covers Of The Ps4 Controller

The front and rear covers of the PS4 controller are prone to collecting fingerprints and other smudges. Luckily, it is relatively easy to clean them if you follow the steps below.

Dampen the cloth with distilled water or isopropyl alcohol and gently wipe down the front cover. Be sure to avoid using harsh chemicals or cleaners, as these could damage the controller.

You can repeat the same process with the rear cover.

After cleaning, dry the covers with a clean cloth.

Next, you can proceed to clean the PS4 controller’s motherboard. You should be extremely careful with this part, as you can easily damage it.

Why You Might Need To Open Your Ps4

How to take apart a PS4 Controller

Most people never need to open their PlayStation 4 console. Sony designed the PS4 to be as user-friendly as possible, and for the most part, it is. With that said, there are some legitimate reasons why you might need to open up your console.

For example, if youre experiencing technical issues that arent resolved by a simple reset, you may need to take apart your PS4 to clean it or inspect it for damage. Additionally, if youre interested in modding your PS4, youll obviously need to open it up to install new components.

In short, there are some occasions where knowing how to open your PS4 is helpful. And while its generally not too difficult to do so, its worth noting that opening your PS4 will void its warranty. So, if youre not comfortable with the idea of potentially damaging your console, its probably best to leave things be.

You May Like: How To Emote In Gta 5 Ps4

Why Is My Ps4 So Loud

Usually, a PS4 will make loud noises if the fan is dirty and dusty.

Another reason it could be loud is because its overheating, so make sure you keep it in a well-ventilated area.

A few more reasons could be:

Youre playing graphic-intensive games which overrun the PS4.
Your hard drive is failing.
The cooling fans are running.
There are loose screws within the console.
The heatsink is damaged.

How To Clean A Playstation Four

A dirty PS4 can soon become a dysfunctional PS4. With dust and debris getting into the fan, your PlayStation will run loud and become laggy.

Were here to teach you how to clean your PlayStation. This method is for the original PS4, but we have some tips for the PS4 Pro and Slim, too.

Well show you how to clean the PS4 fans and the exterior, as well as the controllers. Soon your PS4 will be looking brand new and hopefully running a lot smoother.

How to Clean a PS4

Once youve exposed the fan, spray compressed air into the vent while holding the fan in place. Use a cotton swab to clean the blades. Reassemble the PlayStation and wipe the exterior with cleaning wipes. Remove dust with a can of compressed air or your vacuums nozzle attachment. Wipe the PS4 once more with a dry microfibre cloth.

Get Back to Gaming

Recommended Reading: How To Connect Beats Wireless To Ps4 Bluetooth

Wiping Down The Controller

1Mix 1 part water with 1 part rubbing alcohol. Fill a 1 quart spray bottle a quarter of the way with water. Pour rubbing alcohol on top of the water until it reaches the halfway point. Screw the cap on tightly and gently turn the bottle upside down and back up to mix the solution.XResearch source

Give the bottle a few sprays into the sink to make sure it’s working properly

2Wipe down the controller with the mixture using a microfiber towel. Spray 2 to 3 spurts of your disinfectant onto a clean microfiber towel. Wipe down the entire surface of the controller. Once the clean side of the towel gets dirty, flip it to the other side.XResearch source

You can also use a soft cloth or lint-free paper towel. However, microfiber towels are better at trapping dirt and reducing the risk of scratching glossy parts of the controller.

3Pour 100% rubbing alcohol into a small container. Fill up a small container or tray and place it next to your controller. If you can’t get 100% rubbing alcohol, make sure it’s as close to 100% as possible.XResearch source

4Dip a cotton swab into the rubbing alcohol and squish it. Be sure that the tip is flat after you squish it down with your fingers. Always wear cleaning gloves as you do this to avoid getting alcohol on your skin.XResearch source

After squeezing the cotton, it should be flat enough to get inside the controller’s tight spots.

If you’re having a hard time cleaning the button gaps, focus on the surfaces.

Before You Begin You Need:

A long Phillips screwdriver

Turn off the PS4 console.

Unplug the power, HDMI and any other cables from the rear of your PS4 console.

Place the console on a clean, flat surface in front of you. Turn it over and rotate the console so that the PlayStation logo is facing away from you. Remove the cap from the screw hole directly above the PS logo, as shown.

Insert the screwdriver into the manual eject hole and turn anticlockwise to release the disc. This may require several turns of the screw. There is a layer of plastic that you will need to push through to remove the screw. Don’t worrythis won’t affect the warranty.

Reconnect the power, HDMI and any other cables that were disconnected in Step 1.

Power on the PS4 console to make sure everything is functioning properly.