Sunday, February 5, 2023

How To Take Apart A Ps4

Don't Miss

Soldering The New Hdmi Port

How to take apart PS4 Pro – Complete Teardown

Once everything is clean, you can insert the new HDMI port into the through holes on the board. It should fit right into the large holes, with the smaller pins lining up with the small solder pads.

Next is to solder the small pins of the HDMI port. This is a tricky process, and you will need some form of magnification to see if the small pins are soldered correctly. I didnt have equipment to photograph/film with magnification while I was soldering, so for the solder process I will refer you to this video:

Before You Begin You Need:

  • A long Phillips screwdriver
  • Turn off the PS4 console.
  • Unplug the power, HDMI and any other cables from the rear of your PS4 console.
  • Place the console on a clean, flat surface in front of you. Turn it over and rotate the console so that the PlayStation Logo is facing away from you. Remove the cap from the screw hole directly above the PS Logo, as shown. .
  • Insert the screwdriver into the manual eject hole and turn anti-clockwise to release the disc. This may require several turns of the screw. There is a layer of plastic that you will need to push through to remove the screw. Dont worry this wont affect the warranty.
  • Reconnect the power, HDMI and any other cables that were disconnected in Step 1.
  • Power on the PS4 console to make sure everything is functioning properly.
  • Turn off the PS4 console.
  • Unplug the power, HDMI and any other cables from the rear of your PS4 console.
  • On a clean, flat, surface place the PS4 upside-down, and look for the hole directly above the PS Logo. .
  • Insert the screwdriver into the manual eject hole and turn anti-clockwise to release the disc. This may require several turns of the screw. There is a layer of plastic that you will need to push through to remove the screw. Dont worry this wont affect the warranty.
  • Reconnect the power, HDMI and any other cables that were disconnected in Step 1.
  • Power on the PS4 console to make sure everything is functioning properly.
  • Turn off the PlayStation 4 console.
  • Cleaning The Inside Of The Controller

  • 1Remove the 4 screws from the back of the controller. Flip the controller over. Remove all of the screws by turning each screw counterclockwise with a Phillips #0 flat head screwdriver. Use a 4 to 5 inch screwdriver for the best results.XResearch source
  • Replace the screws if they are difficult to turn. The screws are M2X6 Phillips flat head machine screws.
  • 2Insert a small flathead screwdriver into the crease and lever it open. Press the screwdriver firmly in between the crease at any point along the controller. Begin levering it up until the pieces open. Continue working around the crease until it pops open completely.XResearch source
  • Be gentle when levering open the controller to avoid damaging it.
  • 3Remove the back piece of the controller. Pull the controller apart from the indent on the bottom between the analog sticks. Gently remove the back of the controller by jiggling it up and forward. Take care not to pop the buttons off.XResearch source
  • Spray the back piece with a surface cleaner and dry cloth if it’s dirty.
  • 4Pull out the white ribbon cable from the connector slot. After opening the controller, take care not to break the ribbon cable. Gently remove it from its connector slot with your hands and set the front piece of the controller aside.XResearch source
  • Be patientâthis piece can take a while to shimmy off.
  • Be careful not to break the wires attaching the chipboard to the battery.
  • Reattach any ribbon cables as you reassemble the controller.
  • You May Like: Sign In With Playstation Network

    How To Make A Playstation 4 Quieter Without Taking It Apart

    If youre like millions of people , then youve probably been playing a lot of the Resident Evil 2 remake lately. As you spend hours shooting zombies, you cant help but notice that your PlayStation seems a little worse for wear. Its hot to the touch and its running quite loudly.

    How to make a PS4 Quieter? You can silence a loud PlayStation 4 without taking it apart simply by cleaning it using a portable, handheld vacuum cleaner on the lowest suction setting. Chances are, too much dust is preventing the centrifugal fan from doing its job. This makes the machine work harder to keep you entertained, leading to the troublesome noises.

    You dont want to miss this article, as Ill go in-depth on cleaning your PS4 as well as how to prevent future noise recurrences. Whether your PlayStation is a few months or a few years old, you can soon have it running and sounding as good as the day you bought it.

    What Causes The Hdmi Controller Chip To Break

    Orig launch day PS4: Maybe time to do a teardown ...

    Aside from the HDMI port itself, video problems on the Playstation 4 can also be caused by a defective HDMI controller chip or its surrounding components. If this is the case, then the broken components need to be replaced. This is rather difficult and best left to a professional.

    The HDMI controller chip is a sensitive component and can break due to a variety of reasons:

    • plugging the HDMI cable while the PS4 is on. This is usually fine, but in rare situations it can cause the HDMI chip to get damaged. One of the situations in which this can be an issue is when the grounding between the PS4 and TV is unbalanced.
    • Shorting out of the HDMI port pins. If the pins on the HDMI port short circuit, for example when one pin bends and touches another one, the controller chip can break.
    • Static electricity. If you have opened up the console to repair or clean it, but did not take proper anti-static measures, it is possible that static electricity damaged the controller IC.

    Aside from this, there is also a possibility that there is damage to the HDMI coil filters, or that the traces on the circuit board near the HDMI port are damaged.

    All in all, despite the HDMI port itself often being the culprit, there are also a lot of other possible causes for a Playstation 4 to display no image. As a result, this can be a tricky repair.

    Recommended Reading: Ips Ps4

    How To I Take Apart The Controller

    While we’ve focused on taking you console apart, I think it’s worth mentioning that the controller comes apart as well. There are multiple reasons why you would do this ranging from simple cleaning, to replacing the battery since it is internal and will eventually lose a charge. Follow these steps to get the controller open:

    • Use a Phillips Screwdriver to remove the four screws on the back of the controller
    • Turn the controller over and facing toward you. Using a plastic opening tool, pinch the left shoulder and wedge open the crack on the front of the left grip. Do the same for the right shoulder
    • Turn the controller away from you and use your plastic tool to open the splittings near the share and options buttons on the backside by the light bar.
    • Be careful not to lose the 2 trigger springs or the 1 grey reset button extension when opening this portion.
    • Careful detach the motherboard ribbon to detach the bottom and top halves of the controller.

    At this point you will have the controller full opened and the battery will be exposed. If you need to change the battery out, do so by using blunt forceps to gently unplug the battery from the motherboard. At this point you can take it out and replace it. Now we’ll dive a little deeper to full disassemble it:

    With this knowledge you can replace parts as needed or mod the outer casing as you see fit. Have fun!

    Want to share your experience? Post your tips and techniques below!

    Recommended:

    Ps4 Controller Drift Warranty

    If youre a gamer and own a PS4, chances are youve experienced the controller drifting issue at some point. Sony has been unresponsive to this problem since it first surfaced with many gamers reporting that they have spent hours on the phone trying to get through only to be put on hold or give up in frustration.

    This post will provide readers with information on what is causing controller drift and how users can fix it themselves without having to call Sonys customer service department again.

    Don’t Miss: Ps2 Default Parental Code

    What You Should Prepare For Cleaning Ps4

    To conduct the PS4 cleaning job, you should make some preparations. First and foremost, you should back up your important data on the machine before cleaning PS4. In fact, cleaning the inside of PS4 is rather risky. By doing so, you can prevent data loss due to accident.

    Besides, you should prepare some professional and vital tools for cleaning PS4. They are listed as follows.

    • Screw drivers
    • A can of compressed air
    • Cleaning cloth

    Top recommendation: Are You Bothered by PS4 Froze Issue? Here Are 8 Solutions

    Getting Access To And Removing The Motherboard

    How To Open/Disassemble a PS4

    Unscrew the twelve circled screws. Removing the screws will allow us to remove the large metal plate.

    Do the same with the two larger screws that hold the heatsink clamp.

    Remove the heatsink clamp.

    Unplug the small connector in that area.

    Take the large metal plate out of the console.

    And finally remove the PS4 motherboard. Make sure to lift the right side up first and then pull it out along its length, so that the ports on the left dont get bent or otherwise damaged.

    Don’t Miss: Sony Entertainment Network Deactivate Primary Ps4

    How To Clean A Ps4 Controller

    This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow’s Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards.There are 16 references cited in this article, which can be found at the bottom of the page.The wikiHow Video Team also followed the article’s instructions and verified that they work. This article has been viewed 121,012 times.Learn more…

    If you’re a PlayStation 4 fan, then your controller gets a lot of use. And while it comes into contact with germs often, it’s easy to forget to clean it. If your controller has experienced a lot of wear and is starting to look dirty, it’s time for a clean! Luckily, whether you want to clean your PS4 controller from the outside or inside, the procedure is fairly simple.

    Taking Apart The Ps4 Slim

    Check out the video if you want to see it happen in real-time:

    If you’d like a text version of the process, you’re in luck! We’ve got the only one you’ll find on this side of the internet right here:

    From here, you can continue pulling out pieces like the disc drive if you’d like, but at this point we are past the point of simply cleaning or maintaining the inside. That being said, if you’re disc is stuck, this is the point where you can remove and access the disc drive.

    Next up, the PS4 Pro!

    Don’t Miss: Clearing Cache Ps4

    Taking Apart The Ps4 Pro

    Check out the video above for a quick breakdown, and join us for the text version of the process below:

    • Start by popping off the hard drive cover on the upper left corner of the system’s backside. Only a single Phillips screw here. You’ll need to remove a few more screens before the hard drive is free from the caddy shackles.
    • You’ll need to remove the warranty stickers at this point to go any further. Beneath these, you’ll find the security torque screws, which will require a special tool.
    • Once you’ve pulled this panel up and slid it off, you’ll have a view of the motherboard’s backside protected by a large metal plate.
    • Flip the system over and pop off the panel. No warranty stickers here just yet. From here, you can remove the power supply if you like and clean the fan without the need to void the warranty (assuming you haven’t opened the opposite side.
    • With the power supply removed, you can flip the system back over and get to work removing the covering on the motherboard.
    • You’ll notice the X-shaped bracket beneath the CPU shielding. Taking the motherboard out reveals that the thermal management include a a copper heat sink and pads for six chips on the motherboard.
    • From here, you’ll need to remove the next metal plate that holds the heat pipe. Beneath that you’ll find the fan and optical drive.

    Ps4 Fan Loud: How To Make Ps4 Quieter

    How To Take Apart A Ps4 Controller Without Breaking It

    If youre hearing a strange noise from your PS4 and thinking that its going to take off then youre not alone. Many PS4 owners face this loud fan problem with their console and this terrible sound is just unbearable.

    But, is there anything you can do to make this loud noise to go away? Yes, there are many ways to fix this problem and make your PS4 much quieter. Read on and youll find the best fixes for your loud PS4 fan.

    Recommended Reading: Create Backup Code Ps4

    Guide How To Disassemble Ps4

    Remove the top panel of the PS4 case. It is easy to remove, just pull up until the clamps open.

    Remove one screw that fixes hard drive basket. In addition, remove the hard drive.

    • Step-2
    • Step-3

    On the backside of the PS4, where the connection ports are located, remove stickers, and below them screws that we need to unscrew.

    Now unscrew the four screws, and for this use the T8 Torx screwdriver.

    Next, remove the cover of the PS4 case. Start to open the case from the same side.

    On the backside of cover, you can see dust. Use a brush or napkin for cleaning the case from dust.

    Lets remove the power supply of PS4 game console. First, unscrew three screws T8 Torx. Then unscrew two screws using PH0 screwdriver.

    Disconnect four-wire connector from the power supply. The connector is fixed quite tightly, and if you cannot get it as easily, to disconnect the cable use tweezers.

    Next, using a plastic tool, pull up on the right side, then on the left side. The right side of the power supply will be harder to pull up.

    If there is a lot of dust inside the power supply, it is better to remove this dust. To do this, unscrew the two screws on the power supply and open it for cleaning.

    Disconnect the blue-ray drive cable from the PS4 motherboard. To do this, press the tweezers onto the iron plate and pull the cable to the side.

    Next, unplug the optical drive power connector by lifting it up. In addition, disconnect the Wi-Fi antenna from the motherboard.

    Remove 12 T8 Torx screws .

    How To Take Apart And Clean Your Ps4

    If youve noticed your PS4 making a lot of noise when playing games, chances are its in need of a clean. Given that your PS4 likely sits in the same spot for long periods of time, its little wonder that dust and grit accumulate both on top of and inside the console.

    When that dust and grit enter or obscure the PS4s various ventilation or fan ducts, the fans have to work much harder to cool the CPU and GPU. Thus, your console will start to sound like a jet airplane and eventually might even shut off as a safeguard against critical levels of heat build-up.

    Before you go calling up an electronics repair company though, you might find that giving the system a thorough clean will improve its performance markedly. This can all be done by yourself and is relatively straightforward.

    However, its worth noting that cleaning your PS4 thoroughly will require you to remove pieces of the hardware and take the console apart. This may void your warranty, so only attempt this if youve had your console for a while and are no longer under warranty.

    Read Also: Cancelling Playstation Now

    What Can You Do To Prevent The Hdmi Port From Breaking Or Wearing Out

    Even though the HDMI port on the Playstation 4 is fragile, there are some things you can do to reduce the risk of it breaking.

    • Turn the console off before inserting or unplugging the HDMI cable. This lowers the chance of damage to the HDMI controller chip.
    • Dont move the console around while it is turned on and plugged in. Moving the PS4 around while it is plugged in causes the HDMI connector in the port to move around and possibly cause a short circuit.
    • Dont wrap the cables around the console while they are still plugged in. This might be convenient if you need to move the Playstation 4 and the cables somewhere else, but it creates a lot of unnecessary stress on the HDMI port. Unplug the cables first, before wrapping them around the console.
    • Use a short HDMI extension cable or splitter if you need to frequently plug and unplug the HDMI cable. You can keep it connected to the PS4 all the time and connect to it instead of the PS4 HDMI port. This prevents the port on the console from wearing out.

    How To Disassemble Clean And Reassemble A Ps4 Slim

    How to take apart a PS4 console

    wikiHow is a wiki, similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 46,690 times.Learn more…

    Sometimes video-game consoles can collect a lot of dust, leading to loud noise from the fan, and a lot of heat generated from the heat sink. This makes it crucial to often dismantle and clean the inside of your console in order to maintain its condition. Given that this can be a tedious and complex process,the following steps will demonstrate how to complete this process specifically for a PS4 Slim.

    Read Also: How To Do An Alley Oop In Nba 2k16 Ps4

    More articles

    Popular Articles